Hello all,

I have 2 vista machines. One is domain joined and the other is in workgroup
mode. I cannot seem to map a drive from my workgroup Vista machine to my
domain joined Vista machine. I can, however, map a drive from my domain
joined machine to my workgroup machine.

When I go to view my Network through Windows Explorer I can see the all
computers on my network from my Domain joined Vista machine, but I cannot see
the domain joined Vista machine from my Workgroup machine.

This is also true for Remote Desktop. I can connect one way but not the
other.

I have put the host name in the host file so name resolution works if I
ping. I am able to successfully ping both ways. On my domain machine i have
enabled about every exception on the firewall, but I can't disable it because
it is a company laptop and they have restiricted some control with GPO.

Any ideas on what the problem could be? I also have multiple machines in
Workgroup mode and they all see each other perfectly. all nodes are in the
same subnet. Any help would be greatly appreciated.

Thanks,
am

Do you receive any system error when you use net view command? For example
net view workgroupvistaipaddress.

--
Bob Lin, MS-MVP, MCSE & CNE
Networking, Internet, Routing, VPN Troubleshooting on
http://www.ChicagoTech.net
How to Setup Windows, Network, VPN & Remote Access on
http://www.HowToNetworking.com
"SY" wrote in message
...
Hello all,

I have 2 vista machines. One is domain joined and the other is in
workgroup
mode. I cannot seem to map a drive from my workgroup Vista machine to my
domain joined Vista machine. I can, however, map a drive from my domain
joined machine to my workgroup machine.

When I go to view my Network through Windows Explorer I can see the all
computers on my network from my Domain joined Vista machine, but I cannot
see
the domain joined Vista machine from my Workgroup machine.

This is also true for Remote Desktop. I can connect one way but not the
other.

I have put the host name in the host file so name resolution works if I
ping. I am able to successfully ping both ways. On my domain machine i
have
enabled about every exception on the firewall, but I can't disable it
because
it is a company laptop and they have restiricted some control with GPO.

Any ideas on what the problem could be? I also have multiple machines in
Workgroup mode and they all see each other perfectly. all nodes are in
the
same subnet. Any help would be greatly appreciated.

Thanks,
am

From the Workgroup-mode Vista machine I run net view and I get a list off all
the machines except for the Vista machine (domain-joined). When I run "net
use \\domainJoinedVistaMachine" I get System Error 53 has occured, which is
"The network path was not found". I can, however, ping this machine.

From the Domain-joined Vista machine I can run net view and get "System
error 6118 has occured", which is "The list of servers for this workgroup is
not currently available." When I attempt to run "Net View
\\workgroupVistaMachine" I successfully see all shared resources.

Any help would be appreciated. thanks!
Sam

"Robert L. (MS-MVP)" wrote:

Do you receive any system error when you use net view command? For example
net view workgroupvistaipaddress.

--
Bob Lin, MS-MVP, MCSE & CNE
Networking, Internet, Routing, VPN Troubleshooting on
http://www.ChicagoTech.net
How to Setup Windows, Network, VPN & Remote Access on
http://www.HowToNetworking.com
"SY" wrote in message
...
Hello all,

I have 2 vista machines. One is domain joined and the other is in
workgroup
mode. I cannot seem to map a drive from my workgroup Vista machine to my
domain joined Vista machine. I can, however, map a drive from my domain
joined machine to my workgroup machine.

When I go to view my Network through Windows Explorer I can see the all
computers on my network from my Domain joined Vista machine, but I cannot
see
the domain joined Vista machine from my Workgroup machine.

This is also true for Remote Desktop. I can connect one way but not the
other.

I have put the host name in the host file so name resolution works if I
ping. I am able to successfully ping both ways. On my domain machine i
have
enabled about every exception on the firewall, but I can't disable it
because
it is a company laptop and they have restiricted some control with GPO.

Any ideas on what the problem could be? I also have multiple machines in
Workgroup mode and they all see each other perfectly. all nodes are in
the
same subnet. Any help would be greatly appreciated.

Thanks,
am

System error 53 and 6118 could be name resolution or master browser issue.
Try to use Ip address to new view first. Or check this search result.

System ErrorsSystem error 1219 has occurred - The credentials supplied
conflict with an ... System error 1385 has occurred - Logon failu the
user has not been granted ...
www.chicagotech.net/systemerrors.htm


--
Bob Lin, MS-MVP, MCSE & CNE
Networking, Internet, Routing, VPN Troubleshooting on
http://www.ChicagoTech.net
How to Setup Windows, Network, VPN & Remote Access on
http://www.HowToNetworking.com
"SY" wrote in message
...
From the Workgroup-mode Vista machine I run net view and I get a list off
all
the machines except for the Vista machine (domain-joined). When I run
"net
use \\domainJoinedVistaMachine" I get System Error 53 has occured, which
is
"The network path was not found". I can, however, ping this machine.

From the Domain-joined Vista machine I can run net view and get "System
error 6118 has occured", which is "The list of servers for this workgroup
is
not currently available." When I attempt to run "Net View
\\workgroupVistaMachine" I successfully see all shared resources.

Any help would be appreciated. thanks!
Sam

"Robert L. (MS-MVP)" wrote:

Do you receive any system error when you use net view command? For
example
net view workgroupvistaipaddress.

--
Bob Lin, MS-MVP, MCSE & CNE
Networking, Internet, Routing, VPN Troubleshooting on
http://www.ChicagoTech.net
How to Setup Windows, Network, VPN & Remote Access on
http://www.HowToNetworking.com
"SY" wrote in message
...
Hello all,

I have 2 vista machines. One is domain joined and the other is in
workgroup
mode. I cannot seem to map a drive from my workgroup Vista machine to
my
domain joined Vista machine. I can, however, map a drive from my
domain
joined machine to my workgroup machine.

When I go to view my Network through Windows Explorer I can see the all
computers on my network from my Domain joined Vista machine, but I
cannot
see
the domain joined Vista machine from my Workgroup machine.

This is also true for Remote Desktop. I can connect one way but not
the
other.

I have put the host name in the host file so name resolution works if I
ping. I am able to successfully ping both ways. On my domain machine
i
have
enabled about every exception on the firewall, but I can't disable it
because
it is a company laptop and they have restiricted some control with GPO.

Any ideas on what the problem could be? I also have multiple machines
in
Workgroup mode and they all see each other perfectly. all nodes are in
the
same subnet. Any help would be greatly appreciated.

Thanks,
am