Hello everybody,

i am just trying to get a Samba share up and running on my MSDN Vista
Installation and i´ve got some problems getting it running.

Therefore i want to forward a few ports from my samba-server to my vista
machine with putty/plink over a loopback adapter

on my winXP machine everything works fine:

WinXP--Loopbackadapter -- static ip -- Netbios deactivated -- putty
forwarding of ports 139 and 445 -- net use share ... and mapping the drive
is no problem

No as i tried this under vista i have some strange problems.

I installed the loopback device and made the following adjustments in the
properties area:

- only ipv4 and ms networking is activated
- static ip 10.0.0.1
- subnet 255.255.255.0
- no gateway
- netbios (wins) deaktivated

- routing ports 139 and 445 to my local machine the same way as i do on my
winxp machine

My general Problem is...

Access to shares on server is not available becaus i can´t find the ip

I tried everything... but i cant find a working sollution ...

Perhaps it is a problem with the Vista Networking-Center ... there my
loopback-device or loopback network is always shown as "unidentified Network"
and the "fileshareing" options are always set to "off"

Anyone else out there with the same problem ???

up

"Spaxa" wrote:

Hello everybody,

i am just trying to get a Samba share up and running on my MSDN Vista
Installation and i´ve got some problems getting it running.

Therefore i want to forward a few ports from my samba-server to my vista
machine with putty/plink over a loopback adapter

on my winXP machine everything works fine:

WinXP--Loopbackadapter -- static ip -- Netbios deactivated -- putty
forwarding of ports 139 and 445 -- net use share ... and mapping the drive
is no problem

No as i tried this under vista i have some strange problems.

I installed the loopback device and made the following adjustments in the
properties area:

- only ipv4 and ms networking is activated
- static ip 10.0.0.1
- subnet 255.255.255.0
- no gateway
- netbios (wins) deaktivated

- routing ports 139 and 445 to my local machine the same way as i do on my
winxp machine

My general Problem is...

Access to shares on server is not available becaus i can´t find the ip

I tried everything... but i cant find a working sollution ...

Perhaps it is a problem with the Vista Networking-Center ... there my
loopback-device or loopback network is always shown as "unidentified Network"
and the "fileshareing" options are always set to "off"

Anyone else out there with the same problem ???

???

"thread" wrote:

up

"Spaxa" wrote:

Hello everybody,

i am just trying to get a Samba share up and running on my MSDN Vista
Installation and i´ve got some problems getting it running.

Therefore i want to forward a few ports from my samba-server to my vista
machine with putty/plink over a loopback adapter

on my winXP machine everything works fine:

WinXP--Loopbackadapter -- static ip -- Netbios deactivated -- putty
forwarding of ports 139 and 445 -- net use share ... and mapping the drive
is no problem

No as i tried this under vista i have some strange problems.

I installed the loopback device and made the following adjustments in the
properties area:

- only ipv4 and ms networking is activated
- static ip 10.0.0.1
- subnet 255.255.255.0
- no gateway
- netbios (wins) deaktivated

- routing ports 139 and 445 to my local machine the same way as i do on my
winxp machine

My general Problem is...

Access to shares on server is not available becaus i can´t find the ip

I tried everything... but i cant find a working sollution ...

Perhaps it is a problem with the Vista Networking-Center ... there my
loopback-device or loopback network is always shown as "unidentified Network"
and the "fileshareing" options are always set to "off"

Anyone else out there with the same problem ???

Hi,
I have the same problem whit Vista SP1......whith Vista it worked for
me


--
januarius
Posted via http://www.vistaheads.com