Lost path to boot drive - Help please
 

I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can “boot” into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim

Lost path to boot drive - Help please
 

Hi, Tim.



"TimB" wrote in message
...
I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can “boot” into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim

Lost path to boot drive - Help please
 

Hi, Tim.



"TimB" wrote in message
...
I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can “boot” into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim

Lost path to boot drive - Help please
 

Thanks for the reply. Unfortunately the link doesn't resolve anywhere
when I click on it.

Tim



On Feb 25, 6:48*pm, "R. C. White" wrote:
Hi, Tim.

"TimB" wrote in message

...

I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can boot into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim

Lost path to boot drive - Help please
 

Thanks for the reply. Unfortunately the link doesn't resolve anywhere
when I click on it.

Tim



On Feb 25, 6:48*pm, "R. C. White" wrote:
Hi, Tim.

"TimB" wrote in message

...

I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can boot into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim

Lost path to boot drive - Help please
 

That usually only happens when you boot with the Cloned drive and
the drive you cloned from still attached.
After a clone you are supposed to shut down, remove the old drive and place the
new drive
in its position then reboot.
did you do that??

peter

--
If you find a posting or message from me offensive,inappropriate
or disruptive,please ignore it.
If you dont know how to ignore a posting complain
to me and I will be only too happy to demonstrate :-)

"TimB" wrote in message
...
I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can “boot” into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim

Lost path to boot drive - Help please
 

That usually only happens when you boot with the Cloned drive and
the drive you cloned from still attached.
After a clone you are supposed to shut down, remove the old drive and place the
new drive
in its position then reboot.
did you do that??

peter

--
If you find a posting or message from me offensive,inappropriate
or disruptive,please ignore it.
If you dont know how to ignore a posting complain
to me and I will be only too happy to demonstrate :-)

"TimB" wrote in message
...
I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can “boot” into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim

Lost path to boot drive - Help please
 

Thanks, Peter.

I did have them both connected, but just disconnected the original "C"
drive and rebooted.

I got a BIT farther when the light blue windows screen appeared. It
now tells me that it couldn't find the path/file, etc to RUNDLL32.EXE.
I assume that means that the OS paths are screwed up as the CLONE
drive is still set at drive H: and I cannot see anyway to change it to
drive C, which I assume the OS wants.

Thoughts?
Tim




On Feb 25, 7:05*pm, "peter" wrote:
That usually only happens when you boot with the Cloned drive and
the drive you cloned from still attached.
After a clone you are supposed to shut down, remove the old drive and place the
new drive
in its position then reboot.
did you do that??

peter

--
If you find a posting or message from me offensive,inappropriate
or disruptive,please ignore it.
If you dont know how to ignore a posting complain
to me and I will be only too happy to demonstrate :-)

"TimB" wrote in message

...

I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can boot into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim

Lost path to boot drive - Help please
 

Thanks, Peter.

I did have them both connected, but just disconnected the original "C"
drive and rebooted.

I got a BIT farther when the light blue windows screen appeared. It
now tells me that it couldn't find the path/file, etc to RUNDLL32.EXE.
I assume that means that the OS paths are screwed up as the CLONE
drive is still set at drive H: and I cannot see anyway to change it to
drive C, which I assume the OS wants.

Thoughts?
Tim




On Feb 25, 7:05*pm, "peter" wrote:
That usually only happens when you boot with the Cloned drive and
the drive you cloned from still attached.
After a clone you are supposed to shut down, remove the old drive and place the
new drive
in its position then reboot.
did you do that??

peter

--
If you find a posting or message from me offensive,inappropriate
or disruptive,please ignore it.
If you dont know how to ignore a posting complain
to me and I will be only too happy to demonstrate :-)

"TimB" wrote in message

...

I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can boot into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim

Lost path to boot drive - Help please
 

You must have booted with your origonal c still attached.
Disconnect all drives except the one you want, reboot if it doesnt, use your
win dvd to repair
There is also a vague possibility that your mobo requires the use of a
specific connector for the boot drive.

"TimB" wrote in message
...
Thanks, Peter.

I did have them both connected, but just disconnected the original "C"
drive and rebooted.

I got a BIT farther when the light blue windows screen appeared. It
now tells me that it couldn't find the path/file, etc to RUNDLL32.EXE.
I assume that means that the OS paths are screwed up as the CLONE
drive is still set at drive H: and I cannot see anyway to change it to
drive C, which I assume the OS wants.

Thoughts?
Tim




On Feb 25, 7:05 pm, "peter" wrote:
That usually only happens when you boot with the Cloned drive and
the drive you cloned from still attached.
After a clone you are supposed to shut down, remove the old drive and
place the
new drive
in its position then reboot.
did you do that??

peter

--
If you find a posting or message from me offensive,inappropriate
or disruptive,please ignore it.
If you dont know how to ignore a posting complain
to me and I will be only too happy to demonstrate :-)

"TimB" wrote in message

...

I have a Windows Vista Ultimate system with 4 SATA hard drives
configured to look like IDE drives through an ASUS motherboard.

I had the boot drive set as drive C: with a variety of applications
installed on it. Two days ago I 'cloned' that drive to a new larger
drive with the most recent version of Norton Ghost. That drive showed
as drive H:.

I've been trying to get the new drive to show as drive c:, as all my
applications want to read data or write settings to drive C:. I've
used the disk manager in Vista to change the drive letter assignments,
even swapped the SATA cables between the two and probably some other
settings in BIOS, etc. -- The original boot drive now shows as drive
G: and the 'new' drives shows as H:.

The system is now SO screwed up that although I can boot into
Windows it will not bring up any of my applications and simply shows a
light blue background with no toolbars or icons. I can use Ctrl-Alt-
Del to get into the task manager and try to start a management program
but it always shows 'Path Not Found' and references drive H:.

Can anyone make a suggestion on how I get one of the 'boot' drives
seen as drive C: again and boot into Vista? Maybe even to the point
where I can use the Vista DVD to repair one of them?

Thanks for helping an idiot!
Tim